![]() ![]() Suitable for any modeling putty, Apoxie Sculpt, Greenpower. the head of Allosaurus fragilis, foamcore with Milliput epoxy putty, finished in weatherproof acrylic. Prepared in strict collaboration with Michael Mass of Desert Eagle. We recommend Milliput is stored in cool, dry conditions. michael lovejoy artist sculptor and illustrator. Milliput will set under water and is heat resistant up to 130☌. Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive and should not be used where a paste, mucilage or thin glue is indicated. (it is advisable to wear eye protection during this process). the washer was held in place on the magnet whilst the putty was built up to the. Milliput can be sandpapered and painted immediately it has set. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. ![]() the surface is unfinished with white epoxy putty (Milliput) filled into drill holes before cutting. By the application of heat the setting time can be reduced to a few minutes.Īfter setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Published Saturday, 30 January, 2021By Michael Paige. Speed of hardening is dependant on temperature and at normal temperatures (20-25✬) Milliput becomes rock hard in three to four hours. The two sticks have a long shelf life but once mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. The author gratefully acknowledges Michael Belman. sticks and the general instructions for preparation and usage are the same. highly polished fill of Milliput epoxy putty helps achieve the desired glossy result. putty type of epoxy, use Milliput or a similar modellers ribbon epoxy. MICHAELS MILLIPUT PUTTY PROFESSIONALEach grade is presented in similar packs containing 2 x 56♷gm. kind found in craft stores like Hobby Lobby, Michaels, or Jo-Ann Fabrics. Milliput: Medium Silver-Grey 2-Part Self Hardening Putty (4oz Set) The choice of professional porcelain & pottery restorers, sculptors and master model. ![]() We produce five grades: Standard Yellow/Grey, Silver Grey, Superfine White, Terracotta, and the latest addition - Milliput Black. ![]() Milliput can be sandpapered and painted immediately it has set.Superfine (for porceline) Milliput is the trade name for our epoxy putty. The putty may now be applied and will set hard in three to four hours without shrinking.Īfter setting hard Milliput continues to cure and is fully cured after over five hours at the same temperature. Abrading the surface will improve adhesion. rough up the surface of the plastic a bit. It's great for making jewelry, modelling, and repairing chips, scratches, and other imperfections. Smooth surfaces should be cleaned with a suitable solvent or with soap and warm water to remove dirt and grease. Michael Hatch has used the PART sets to great effect on a Revell Tiger kit. Milliput Superfine White Epoxy Putty is a versatile two-part epoxy putty that is specially formulated for the resotration of items where a fine finish is desired such as porcelain and ceramics. MICHAELS MILLIPUT PUTTY FREEThe surfaces to which the putty is applied should be free from grease and dirt. The Part A resin component of most 2-part polyurethane resins comes with a certain amount of filler already included. Knead and roll in the hands for at least 5 minutes until the colours merge and become uniform and no streaks can be seen, and then mix for another minute. Mix together equal parts of each stick from the pack. It is very important when using Milliput that you mix the two parts for at least five minutes.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |